Burglar Alarms

Burglar Alarm Surge Suppression

1PRJ11: If your power side of the system is connected by plug-into 110-volt AC, this unit has one outlet and should be installed in front of the plug-in transformer.

D Dual 2W 15V: 15 Volts DC to be used on the Contact/Sensor loops or dedicated (non-ring type) modem lines.

DLT 1P 200: Installation: Connect the red and green leads to terminal 4 and 5. Install the unit as close to the RJ31X Telco Block as possible and keep the leads from the DLT 1P as short as possible. Run the ground wire to the nearest AC unified earth ground.

T12MD: 12 Volts DC to be used on the initiating circuits, addressable loops, and NAC loops operating at 12Volts DC drawing less than 5 amps. These 2 pair / 4 wire surge protection devices have screw terminals (4 in and 4 out)

T12MDP: 12 Volts DC to be used on the initiating circuits and addressable loops operating at 12Volts DC drawing less than 150 milliamps. These 2 pair / 4 wire surge protection devices have screw terminals (4 in and 4 out)

T120MDP: 130Volts RMS to be used on equipment connected to your telecommunication lines with ring voltage. i.e.(RJ31X) alarm dialers etc. This 2 pair / 4 wire surge protection device has removable screw terminals (4 in and 4 out) for ease of installation and or replacement.

RJ31120MDP: 130Volts RMS to be used on equipment connected to your telecommunication lines with ring voltage with RJ31X connection. This device has Female RJ31X connectors (1 in and 1 out).

Displaying products 1 - 8 of 8 results
1PRJ11 - 120V AC Plug-In 1 Outlet Wall Mount Surge Protector - 15 Amp + Telephone
Part Number: 1PRJ11
Price: $20.00
1PRJ11 - 120V AC Plug-In 1 Outlet Wall Mount Surge Protector - 15 Amp + Telephone
The 1PRJ11 surge protector provides 1 AC outlet and 2 RJ11 outlets for telephone, fax, or modem protection. This unit has an automatic reset and will take surge after surge. This product is UL 1449 Listed.
DLT1P200 - 200V Telephone Surge Protector Model DLT1P200
Part Number: DLT1P200
Price: $30.00
DLT1P200 - 200V Telephone Surge Protector Model DLT1P200
DLT1P200 is self-restoring after each surge within ratings. Installation is typically at the box where the service enters the building or on the punch blocks. This model is for regular telephone lines. Tested to ANSI/IEEE B3 impulse standards UL497 listed
DLTTOS200 - 200V DC ILDCP Series - Isolated Loop Circuit Protector for Communication Lines - Hybrid Inline Series
Part Number: DLTTOS200
Price: $75.00
DLTTOS200 - 200V DC ILDCP Series - Isolated Loop Circuit Protector for Communication Lines - Hybrid Inline Series
200V DC Multi stage hybrid protection for your communication lines. Tested to ANSI/IEEE B3 impulse standards and UL 497B. It is self-restoring after each surge within ratings. The ILDCP is available with RJ11 or terminal block termination.
FA15 - 12V 3-Stage Initiating/Data Circuit Protector 2 wire
Part Number: FA15
Price: $75.00
FA15 - 12V 3-Stage Initiating/Data Circuit Protector 2 wire
Hybrid 12 Volt DC Isolated Loop Circuit Surge Protector. Multi stage hybrid protection for your communication lines. Tested to ANSI/IEEE B3 impulse standards and UL 497B. It is self-restoring after each surge within ratings.
MRJ31120MDP - RJ31X Telecom Surge Protector
Part Number: MRJ31120MDP
Price: $59.98
MRJ31120MDP - RJ31X Telecom Surge Protector
ECLIPS RJ31X Telephone Line Protector for Alarm Panels. The EClips MRJ31120MDP incorporates state of the art technology and provides multi stage hybrid protection for your communication lines. Tested to UL standards and is UL listed.
MT120MDP - 120V DC DIN and Snap Rail Mount Surge Protector
Part Number: MT120MDP
Price: $79.98
MT120MDP - 120V DC DIN and Snap Rail Mount Surge Protector
ECLIPS Dual Screw Terminal Telephone Line Protector for Alarm Panels ECLIPS Model MT120MDP Multi stage hybrid protection for your communication lines. Tested to UL standards and is UL listed. It is self-restoring after each surge within ratings.
MT12MD - 12V DC DIN and Snap Rail Mount Surge Protector
Part Number: MT12MD
Price: $69.98
MT12MD - 12V DC DIN and Snap Rail Mount Surge Protector
EClips 12 Volt DC Loop Circuit Protector. Burglar Alarm Protection ECLIPS Model MT12MD provides multi stage hybrid protection for your 12 Volt DC Equipment. Tested to UL497 Standards and is UL listed. It is self-restoring after each surge within ratings.
MT12MDP - 12V DC DIN and Snap Rail Mount Surge Protector
Part Number: MT12MDP
Price: $79.98
MT12MDP - 12V DC DIN and Snap Rail Mount Surge Protector
EClips 12 Volt DC Loop Circuit Protector. Burglar Alarm Protection ECLIPS Model MT12MDP multi stage hybrid protection for your 12 Volt DC Equipment. Tested to UL497 Standards and is UL listed. It is self-restoring after each surge within ratings.