Access Control

E-Clips Surge Suppression products for Card Access Systems

E120H or 120H-PT: If your power side of the system requires a hardwire connection, this 120 Volt AC 3-Wire Single Phase device should be installed as close as possible to the equipment being protected. This is an parallel (AC) surge suppressor and is designed to stop surges from getting to the PLC (Mother Board/Computer Board). The E120H provides both common and normal mode protection. UL 1449 3rd Edition.

1PRJ11: If your power side of the system is connected by plug-into 110-volt AC, this unit has one outlet and should be installed in front of the plug-in transformer.

DLT 3S 200 or DLT TOS 200 or DLT 3S200 DSL 200 Volts DC to be used for modems connected to telecommunication line with ring voltage. The DLT 3S/200 has RJ11 connection (jack/plug) and the DLT TOS 200 has screw terminal connection (hardwire). The DLT3S200 DSL has RJ11 connection (jack/plug) for your 56K or DSL line.

D Dual 2W 15V: 15 Volts DC to be used on the Contact/Sensor loops or dedicated (non-ring type) modem lines.

D Dual 4W or D Dual 6W: For the data side specify 6.8 Volts DC, 15 Volts DC, 30 Volts DC depending on your system, 4W for four wire and 6W for six wire. These units are designed to protect the Mother Board/Computer Board, and the Card Reader.

ILDCP Series Models: These are UL listed 497B in-line series screw terminal multi-stage hybrid devices. These units are designed to protect the equipment with its close clamping ability at high-induced voltages. There is a ground lug/wire provided. Only use if you have a common ground i.e. single ground for entire system to prevent ground loops.

All grounding of low voltage surge suppressors must ground on the shield or the 5th wire used for shield/grounding. The shield/ground must be grounded to the system ground. The system must ground to only one ground source to avoid a ground loop (more than one ground). Normally you will find one ground on the AC power area or main panel ground.

Displaying products 1 - 14 of 14 results
1208CS-T - 120V AC Plug-In 8-Outlet Protector with EMI & RFI Filtering - 15 Amp - 6' Cord
Part Number: 1208CS-T
Price: $59.95
1208CS-T - 120V AC Plug-In 8-Outlet Protector with EMI & RFI Filtering - 15 Amp - 6' Cord
Multi-Stage 120V Hybrid surge protector. The 1208CS-T unit is rated UL 1449 3rd Edition. Six of the Eight outlets on this strip rotate to fit larger transformers. Built for 15 amps of current with a built in circuit breaker.
1PRJ11 - 120V AC Plug-In 1 Outlet Wall Mount Surge Protector - 15 Amp + Telephone
Part Number: 1PRJ11
Price: $20.00
1PRJ11 - 120V AC Plug-In 1 Outlet Wall Mount Surge Protector - 15 Amp + Telephone
The 1PRJ11 surge protector provides 1 AC outlet and 2 RJ11 outlets for telephone, fax, or modem protection. This unit has an automatic reset and will take surge after surge. This product is UL 1449 Listed.
D DUAL 4W 15V - 3 Stage Data Line Surge Protector - Screw Terminal In/Out (4-Wire)
Part Number: DDUAL4W15
Price: $90.00
D DUAL 4W 15V - 3 Stage Data Line Surge Protector - Screw Terminal In/Out (4-Wire)
The E-Clips 12V DC 4 Wire ILDCP incorporates state of the art technology and provides multi stage hybrid protection for your data & video lines. Tested to ANSI/IEEE B3 impulse standards and UL 497B.
D DUAL 4W 30V - 3 Stage Data Line Surge Protector - Screw Terminal In/Out (4-Wire)
Part Number: DDUAL4W30
Price: $90.00
D DUAL 4W 30V - 3 Stage Data Line Surge Protector - Screw Terminal In/Out (4-Wire)
The E-Clips 24V DC 4 Wire ILDCP incorporates state of the art technology and provides multi stage hybrid protection for your data & video lines. Tested to ANSI/IEEE B3 impulse standards and UL 497B.
D DUAL 4W 6.8V - 3 Stage Data Line Surge Protector - Screw Terminal In/Out (4-Wire)
Part Number: DDUAL4W6.8
Price: $90.00
D DUAL 4W 6.8V - 3 Stage Data Line Surge Protector - Screw Terminal In/Out (4-Wire)
The E-Clips 5V DC 4 Wire ILDCP incorporates state of the art technology and provides multi stage hybrid protection for your data & video lines. Tested to ANSI/IEEE B3 impulse standards and UL 497B.
D DUAL 6W 15V - 3 Stage Data Line Surge Protector - Screw Terminal In/Out (6-Wire)
Part Number: DDUAL6W15
Price: $120.00
D DUAL 6W 15V - 3 Stage Data Line Surge Protector - Screw Terminal In/Out (6-Wire)
The E-Clips 12V DC 6 Wire ILDCP incorporates state of the art technology and provides multi stage hybrid protection for your data & video lines. Tested to ANSI/IEEE B3 impulse standards and UL 497B.
D DUAL 6W 30V - 3 Stage Data Line Surge Protector - Screw Terminal In/Out (6-Wire)
Part Number: DDUAL6W30
Price: $120.00
D DUAL 6W 30V - 3 Stage Data Line Surge Protector - Screw Terminal In/Out (6-Wire)
The E-Clips 24V DC 6 Wire ILDCP incorporates state of the art technology and provides multi stage hybrid protection for your data & video lines. Tested to ANSI/IEEE B3 impulse standards and UL 497B.
D DUAL 6W 6.8V - 3 Stage Data Line Surge Protector - Screw Terminal In/Out (6-Wire)
Part Number: DDUAL6W6.8
Price: $120.00
D DUAL 6W 6.8V - 3 Stage Data Line Surge Protector - Screw Terminal In/Out (6-Wire)
The E-Clips 5V DC 6 Wire ILDCP incorporates state of the art technology and provides multi stage hybrid protection for your data & video lines. Tested to ANSI/IEEE B3 impulse standards and UL 497B.
DLT3S200 - RJ11 - ILDCP Series - Isolated Loop Circuit Protector for Communication Lines - Hybrid Inline Series
Part Number: DLT3S200
Price: $75.00
DLT3S200 - RJ11 - ILDCP Series - Isolated Loop Circuit Protector for Communication Lines - Hybrid Inline Series
ILDCP incorporates state of the art technology and provides multi stage hybrid protection for your communication lines. Tested to ANSI/IEEE B3 impulse standards and UL 497B. The ILDCP is available with RJ11 or terminal block termination.
DLT3SDSL - RJ11 DSL - ILDCP Series - Isolated Loop Circuit Protector for Communication Lines - Hybrid Inline Series
Part Number: DLT3SDSL
Price: $75.00
DLT3SDSL - RJ11 DSL - ILDCP Series - Isolated Loop Circuit Protector for Communication Lines - Hybrid Inline Series
ILDCP incorporates state of the art technology and provides multi stage hybrid protection for your communication lines. Tested to ANSI/IEEE B3 impulse standards and UL 497B. The ILDCP is available with RJ11 or terminal block termination.
DLTTOS200 - 200V DC ILDCP Series - Isolated Loop Circuit Protector for Communication Lines - Hybrid Inline Series
Part Number: DLTTOS200
Price: $75.00
DLTTOS200 - 200V DC ILDCP Series - Isolated Loop Circuit Protector for Communication Lines - Hybrid Inline Series
200V DC Multi stage hybrid protection for your communication lines. Tested to ANSI/IEEE B3 impulse standards and UL 497B. It is self-restoring after each surge within ratings. The ILDCP is available with RJ11 or terminal block termination.
FA15 - 12V 3-Stage Initiating/Data Circuit Protector 2 wire
Part Number: FA15
Price: $75.00
FA15 - 12V 3-Stage Initiating/Data Circuit Protector 2 wire
Hybrid 12 Volt DC Isolated Loop Circuit Surge Protector. Multi stage hybrid protection for your communication lines. Tested to ANSI/IEEE B3 impulse standards and UL 497B. It is self-restoring after each surge within ratings.